Introduction
We love some good LED blinking as much as the next person but after years of LED-soldering we need something cooler to get us excited. Sure there are RGB LEDs and those are fun too but what comes after that? Well, we have the answer: LED Strips! These are flexible circuit boards with full color LEDs soldered on. They take a lot of LED-wiring-drudgery out of decorating a room, car, bicycle, costume, etc. The ones we carry are also waterproof (although not all are).

There are two basic kinds of LED strips, the "analog" kind and "digital" kind. Analog-type strips have all the LEDs connected in parallel and so it acts like one huge tri-color LED; you can set the entire strip to any color you wan, but you can't control the individual LED's colors. They are very very easy to use and fairly inexpensive.

The Digital-type strips work in a different way. They have a chip for each LED, to use the strip you have to send digitally coded data to the chips. However, this means you can control each LED individually! Because of the extra complexity of the chip, they are more expensive.

RGB LED Strip Light knowledge

Current draw
Because there are three LEDs in series, you cannot drive these LEDs from a 5V supply. The LED strips say "+12V" on them to mark the anode and that's the maximum voltage we suggest. We've found that if you're ok with them being a little dimmer, even 9VDC works very well.

Each segment draws approximately 20 milliAmperes from a 12V supply, per string of LEDs. So for each segment, there is a maximum 20mA draw from the red LEDs, 20mA draw from the green and 20mA from the blue. If you have the LED strip on full white (all LEDs lit) that would be 60mA per segment.

To find the total maximum current draw per meter, we would multiply 60mA x 10 (ten segments per meter) = 0.6 Amps per meter. Again, that's assuming you would have all the LEDs on at once and that you are powering it from 12V. If you're going to be PWM-fading between colors, maybe 1/2 of that is what you'll be drawing. Still, you do need to have a fairly decent power supply to run this strip, all those LEDs add up!

Usage
Because these LED strips are very simple, we can easily use them with any microcontroller. We suggesting using PWM dimming techniques to control the strip. Since each 'LED' pin may end up requiring an Amp or more to sink to ground, power transistors are required! Don't try to connect the pins directly to your everyday microcontroller, they will burn out and/or not work.

You can use any power NPN or N-Channel MOSFET, make sure the transistor is rated to be able to pass as much current as you need. For example, since we draw about 0.2Amps per channel per meter, if you have a 5 meter strip you will need to pass up to 1 Ampere per transistor. Get the beefy "TO-220" packages, not the dinky little guys. Make sure they look like this:

1. Himax to Mass Produce White LED Driver ICs
2. LG Introduces LH90 Series LED LCD HDTV in the U.S.
3. FakeTV Uses LEDs to Thwart Thieves
4. Elation Releases the ELED Series of White MR16 LED
5. LedEngin Introduces White 40W LED Light Source Exc
6. First Eco-Friendly McDonald’s Lit with Cree LED L
7. Evident Technologies Launched Nanotechnology-Based
8. OSRAM High Performance LEDs Brighten up One of The
9. Everlight Acquires Tecore Shares to Secure LED Chi
10. Sharp Expands LED Backlit Display Line with New Mu

• Wide applicability，easy to install and maintain, long lifespan. （warranty:1 year）

• Very flexible, easily be curved to any shape. Various colors available.

• Extremely luminous，with wide viewing angle.

• Energy saving and environmental conservation,

• Linear separable LED strip on flexible printed circuit board with self-adhesive back.

• Each unit of 3 LEDs can be cut out as a regular segment without damaging the rest ribbon.

• Cables and DC connectors is optional

• ODM/OEM is available